18650/26650 Li-ion Lithium Battery ZB2L3 Tester LCD Meter Voltage Capacity For Sale
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
18650/26650 Li-ion Lithium Battery ZB2L3 Tester LCD Meter Voltage Capacity:
$3.98
18650/26650 Li-ion Lithium Battery ZB2L3 Tester LCD Meter Voltage Capacity
Lithium meter tester without CaseDescription:
This document describes the PZEM-005 multifunction tester model specicications, the multifunction tester is mainly usned to display the battery voltage,battery lever, load current and load resistance.
Function:
1. Measure the battery voltage
Range:2.8~30 V
Resolution:0.1V
Accuracy:2%
2. Measure the battery capacity
Battery capacity is the battery grid form on the LCD display,a total of five grids.Battery capacity is distinguished by the battery voltage.
Displaying 5 grids stands for full capacity,4 grids for 4/5 capacity,3 grids for 3/5 capacity,2 grids for 2/5 capacity,1 grid for 1/5 capacity,0 grid for 0/5 capacity.
Can be set the full capacity 2.9~30.0V,the exhausted 2.8-29.9V
3. Measure the current
Range:0~10.0A
Resolution:0.1A
Accuracy:2%
4. Measure the resistance of the load
Range: 0～999Ω,when over 999Ω display \"oL\"
Resolution:when less than 10Ω,resolution is 0.01Ω;
when less than 100Ω,resolution is 0.1Ω;
when less than 1000Ω,resolution is 1Ω;
Accuracy:2%
5. Back light
Default off-backlight,you can turn on/off the backlight by button.
Note:
Battery >2.8V
Working temperature: -10\'C ~ +40\'C
NOTE: It is without the case !
Package Included:1 * LCD Battery meter Without case
Lithium meter tester with case
Description:
This item can test phone, power bank ,18650 18350 26650 lithium battery
Battery voltage measurement
Measuring range: 2.8 ~ 30.0 V.
Resolution: 0.1 V
Accuracy: 2%.
Quantity of electricity measurement
When Full capacity will show 5 grid , 20% capacity will show 1 grid , When the cut-off voltage of the battery will display 0 grid .
When the voltage of the electrical measurement set at full charge, the battery cut-off voltage is set to zero power.
Battery cut-off voltage can be set, the range set for 2.8 ~ 30.0V, but not more than the full-scale voltage.
Full range voltage of the battery can be set, the range set for 2.8V ~ 30.0V, but not less than the cut-off voltage .
Load current measurements
Measuring range: 0.0 ~ 10.0 A.
Resolution: 0.1 A.
Accuracy: 2%.
Load resistance measurement
Load resistance is calculated by battery voltage divided by the load current.
Measuring range: 0 ~ 999 Ω, greater than 999 Ω show \"oL\"
Resolution: when the resistance is less than 10 Ω, a resolution of 0.01 Ω, when resistance is greater than or equal to 10 Ω and less than 100 Ω, a resolution of 0.1 Ω, when the resistance is greater than or equal to 100 Ω and less than 1000 Ω Ω a resolution of 1.
Accuracy: 2%
Backlight control
when connect power the Backlight default is not bright ,Through buttons control the backlight on and off
Battery cut-off voltage and full range voltage Settings
Long press button for 3 seconds to enter the battery cut-off voltage and full range voltage setting state
After entering the state, display the current battery voltage area flicker by voltage, and zero power battery symbol indicates the current is cut off voltage setting state ;At this time can be adjusted through short press button to add 1, long press buttons can be adjusted quickly add 1;
When there is no button operation more than 3 seconds, automatically entered into a state of full range voltage setting
After entering the state, display the current battery voltage area flicker full electric voltage, with full power battery symbol tip is currently full range voltage setting state ;Set the method same as the cut-off voltage setting
When there is no button more than 3 seconds, automatically saved and saved without errors automatically exit, if the value is not correct or save the error shows Err SAu 1 second, and exit
Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Please understand, Thank you.
Package includes:1 x battery tester With caseLithium meter tester HW-586100% brand new and high quality
Material: Electrical components
HW-586 battery capacity tester discharge type 1.2-12V external load capacity of the battery and other tests 18650
Tools, single-function, by controlling the load off and get real-time integrated discharge current capacity results
Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge
Maximum capacity statistics support 9999Ah (9999000mAh)
Automatically identify and develop appropriate battery termination voltage can also be manually adjusted
Specifications:
Power supply voltage: DC4.5-6V (micro USB connector)
Operating Current: less than 70mA
Discharge voltage: 1.00V-15.00V 0.01V resolution
Termination voltage range: 0.5-11.0V
Supported by current: 3.000A 0.001A resolution
Maximum voltage measurement error: 1% + 0.02V
Maximum current measurement error: 1.5% + - 0.008A
Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value by shifting the decimal point to switch, when the display is less than 10Ah X.XXX, as shown above to achieve 10Ah XX.XX, and so on.
Board size: 50mmX37mm
Finished Size: 50mmX37mmX17mm (length X width X height maximum position size, contains copper foot height)
Instructions:
1. The first test should be fully charged battery.
2. Connect the battery to be tested positive to positive input, a negative input to the negative, can not be reversed (with load reversal may damage the circuit)! Load connected to the output of the positive and negative output, to work through the tester micro USB power supply (not available desktop or laptop USB powered), then the battery voltage.
3. Direct start test need only one press of the \"OK\" button, the tester can automatically develop an appropriate termination voltage of the battery full charge voltage, and will start flashing after the test three times. Need to develop artificial termination voltage only when the battery voltage display state by pressing \"+\" or \"-\" buttons to modify the termination voltage display beginning with P, behind the representative voltage resolution 0.1V, set up after pressing the \"OK \"start testing.
4. After the start of the test the tester will control the load of the electronic switch is turned on, the test data shows that the process will release capacity (Ah), current discharge current (A) and battery voltage (V) between the wheel was. When the battery voltage reaches the set cut-off voltage, load control switches off the tester display data stays in capacity (Ah) and above and the corresponding indicator flashes quickly together, now displays the actual capacity of the battery is discharging capacity, about the press \"OK\" to terminate flashing allows stable data display, press again \"OK\" button to return to the power-on state can just replace the battery test the next section ......
Error codes and their meanings:
Err1: battery voltage is above 15V
Err2: battery voltage is lower than the termination voltage
Err3: Battery can not afford to load or discharge current line too much resistance
Err4: overcurrent (current exceeds 3.1A)
This circuit voltage in order to improve the measurement accuracy, specially designed DC bias, when the terminal displays nothing then a small voltage does not affect the actual measurement, if you are shorting the input terminals (absolute 0V) will show 0Note: Use the resistance of the discharge process, resistive load will seriously heat, please pay attention to safety!
Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!
Package Included:1Pc x battery capacity tester .1Pc x Load resistorsLithium Battery USB CableDescription:
The USB battery charger cable with JST plug, output 3.7V 500ma, is suit for JST 3.7V(1S) Lipo battery.
Note: For Lipo battery only, do not use for Ni or Ni-Cd battery.
Package included:1x USB battery charger cable (Not included battery)
- Payment must be received in 5 business days of sale closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day maintain high standards of excellenceand strive for 100% customer satisfaction!response is very important to us. We request that you contact us immediately BEFORE you give us neutralor negativeresponse, so that we can satisfactorily address your package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can\'t take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Related Items:
BT-C3400 V31 Opus Battery Charger Analyzer Li-ion 18650 26650 3100 NiMH AA AAA C
$44.18
18650/26650 Li-ion Lithium Battery ZB2L3 Tester LCD Meter Voltage Capacity
$6.50
10PCS 3S 60A Charging Protection Board 12.6V BMS Balance For 18650 Li Battery US
$19.99
