DC 3V-15V delay timer timing switch module 1sec~20hours1500mA for relay switc VG For Sale

DC 3V-15V delay timer timing switch module 1sec~20hours1500mA for relay switc VG


This item has been shown 9 times.

Buy Now

DC 3V-15V delay timer timing switch module 1sec~20hours1500mA for relay switc VG:
$3





No output power, the output trigger only. (Positive control off).
Function descriptor:
1. After the power, Vo output terminal has no output, Vi-ended input trigger high-level signal, Vo output-side output high, the delay period of time, Vo output terminal has no output. Or: After power, Vo output terminal high level. Vi-ended input triggered high-level signal, Vo output terminal has no output, after a period of delay, Vo output terminal high level. More than two kinds of modes can be selected via a jumper on the module free.
2. The delay time adjustment range of about 1 second to 20 hours;
3.Vo output of low output drive capability of up to 1500mA (short time allowed 2500mA).
4. Power supply voltage: DC 3V-15V
5. The maximum operating current module: At43: 3V ---- 0.7mA 5V ---- 1.3mA 12V ---- 3.6mA ; At43H: 3V---0.3mA 5V---0.6mA 12V---1.7mA 24V---4.4mA The longer execution time, power consumption is smaller.
Note:When using the module, load the negative power supply is negative, the positive connection module Vo end load. That is the positive control of the load off. Internal module with protection diodes and power supply decoupling capacitors, can be directly connected to an inductive load such as a relay, no longer parallel diode of the coil.
This module not only small, large timing range, but with a time proportion jumper timing applications for a long time, do not consume a lot of time in the adjustment process.
Purpose: delay switch, timer.
Instructions:
1. The delay time can pass on module comes with adjustment potentiometer, ranging from about 1 second to 20 hours, see below explanation.
2.Vo Output level can be set by a jumper, see below explanation.

1,2,3 three-pin used to set the timing range, 1-2 communicating timing of 1S-290S adjustable; 2-3 connectivity, timing expand 256 times for 256 seconds -20.5 hours adjustable.
4,5,6 three-pin state is used to set the module's output terminals Vo, 4-5 connectivity, no output power on the initial state, after the trigger has an output, no output after timing; 5-6 connectivity, power-on initial state there is output, no output after the trigger, regular time to recover after output.
Counterclockwise adjustment potentiometer, time is reduced, clockwise adjustment potentiometer time increases. Timing range jumper in the timing of two locations for the 256: 1 relationship. Suppose need eight hours delay, you can use the jumper to 1-2 communicating, the delay time was adjusted to 8/256 = 0.03125 (h) = 112.5 (seconds), and then the two-pin jumper to 2-3 communicating it. This greatly shortens the debugging time. Debugging process requires self stopwatch.
Size: Free of pin size 15mm × 11mm × 8mm. Pin pitch 2.54mm.
Note: 1. The above parameters were measured at 5V, may be slightly different at other voltages; 2. Non-precision circuit requiring high NA and important occasions. Pin definitions: Vcc: Power; Vo: output; Vi: trigger signal input (high level trigger); Gnd: Power Ground
Package Included: 1x Adjustable Delay Timer Module


Buy Now

Manitowoc Ice Sensor Mew 1065 600k 8pin Relay picture
Manitowoc Ice Sensor Mew 1065 600k 8pin Relay


Idec Rh4b-u Relay 24v W/ Idec Sh4b-05 Base 10a 300v Used picture
Idec Rh4b-u Relay 24v W/ Idec Sh4b-05 Base 10a 300v Used


Rh2b-u Idec Relay Dc12v With Sh2b-05 Idec Relay Socket, 10a  (used) picture
Rh2b-u Idec Relay Dc12v With Sh2b-05 Idec Relay Socket, 10a (used)


Allen Bradley 700-ha32z24-4 Ser D Relay With 700-hn125 Ser A Base Used picture
Allen Bradley 700-ha32z24-4 Ser D Relay With 700-hn125 Ser A Base Used


Popular Forums