DIY Electronic Kit Parts Production Tesla Coil Kit mini Music Loudspeaker Kit For Sale
This item has been shown 59 times.
DIY Electronic Kit Parts Production Tesla Coil Kit mini Music Loudspeaker Kit:
$9
1. Introduction
The Tesla Referral coil can produce high temperature and high pressure plasma, which can sing, ignition, wireless transmission, and light fluorescent lamp. It has a wonderful arc. It is a very interesting small production of scientific experiments. This is DIY Tesla Referral coil Kit parts, which needs to be soldered and assembled by yourself.
2.Parameter
1>. PCB size: 4.0mm*8.0mm
2>. Power: 15W
3>. Power input: DC 15-24v. The current is 2A. DC5.5 interface / pin
4>. Audio input: 3.5 socket, can be connected to mobile phone, MP3, computer audio
3. Function
Tesla Referral coil is a transformer that operates on resonance principle. It was invented by Nicola Tesla Referral, a Serbia American scientist in 1891. It is mainly used to produce ultra high voltage, but low current, high frequency AC power. The Tesla Referral coil is composed of two groups of resonant circuits (sometimes three groups) coupled. The Tesla Referral coil is difficult to define, and Nicola Tesla Referral has tried a large number of configurations of various coils. Tesla Referral uses these coils to carry out innovative experiments, such as electrical lighting, fluorescence spectrum, X ray, high frequency alternating current phenomenon, electrotherapy and radio energy transmission, transmitting and receiving radio signals.
4.Feature
1>. Electric arc function: the traverse of the rear end will produce an arc. The arc can also ignite.
2>. Septum light function: after the Tesla Referral coil is electric, the fluorescent lamp can be lighted apart.
3>. Music playback function: a new concept loudspeaker for electric arc to stimulate air to make air vibration produced by plasma. You can play mobile / computer music, but the sound is small.
5.Component listing
NO.
Component Name
PCB Marker
Parameter
QTY
1
Metal Film Resistor
R1,R4
10K
2
2
Metal Film Resistor
R3,R5
2K
2
3
TIP41
Q2
1
4
LED
LED1,LED2
3mm
2
5
Audio Socket
J2
1
6
Electrolytic Capacitor
C1
1uf
1
7
Ceramic capacitor
C2
1uf
1
8
IRF530
Q1
1
9
Power Socket
J1
5.0*2.1mm
1
10
Primary coil
L1
2-3T(Cable)
1
11
Secondary coil
L2
350T
1
12
Copper pillar
M3*10
4
13
Screw
M3*6
4
14
Heat sink
2
15
Light
1
16
PCB
40*76mm
1
6.Note:
1>.There is no direct contact between the primary coil and the secondary coil, and the gap must be reserved, otherwise it may not work properly.
2>.The winding direction of the secondary coil must be consistent with the picture, otherwise it will not work properly.
7.Frequently asked questions
1>.Why the finish kit only LED light?
The wire winding direction should be counterclockwise , different direction will make the current flow different , wrong direction will make the kit doesn't work.
Another important is the wire which wrapped around the Tesla Referral coil , shouldn't touch Tesla Referral coil , must have a gap between them.
If you afraid the wire will touch , you could let the wire with loose wrapp.
2>.The wire winding is correct , why the item still not work?
I have a test , when the Voltage is 15-19V, the kit doesn't have the spark , but when i make the voltage up to 20V, so surprise. Beautiful spark and creative miracle.
3>.Can I touch the spark with my finger?
You could touch it with very very fast speed, it's dangerous , if you stay more time , your finger will be hurt. There is magical effectafter you touch it with a fast speed, the spark will become a round Tesla Referral ring.And the greater the amplitude of the sway, the wider the diameter of the ring.
Children must be accompanied by an adult.
4>.What's the staliness ball function(If you have not purchased separately, please ignore this issue)?
You could use the ball to touch the spark and pull distance slowly , can't exceed 10cm , you could see the purple Tesla Referral spark , very interesting.
Another you could pull the ball on the top of coil,also could produce sparks.
8Installation Steps
Tips:
1>. Install small components at first;
2>. Install complex components preferentially;
3>. Pay attention to the installation direction of components.
4>. Make sure the soldering iron does not touch the components for a long time.Otherwise it is easy to damage the components.
Xr4739cp 4 Pin Ic. Dual Operational Amplifier
Electrical Equipment Extension Patch Cord Connectors Jumper Cable Fiber Optic
Electrical Equipment Extension Patch Cord Connectors Jumper Cable Fiber Optic
Electrical Equipment Extension Patch Cord Connectors Jumper Cable Fiber Optic
