ESP32 Dev Module WiFi + Bluetooth 4MB Flash Development Module 4MB Flash Memory For Sale

ESP32 Dev Module WiFi + Bluetooth 4MB Flash Development Module 4MB Flash Memory


This item has been shown 37 times.

Buy Now

ESP32 Dev Module WiFi + Bluetooth 4MB Flash Development Module 4MB Flash Memory:
$12

Similar Items Description

Power Pins:
GND - this is the common ground for all power and logic
BAT - this is the positive voltage to/from the JST jack for the optional Lipoly battery
USB - this is the positive voltage to/from the micro USB jack if connected
EN - this is the 3.3V regulator's enable pin. It's pulled up, so connect to ground to disable the 3.3V regulator
3V - this is the output from the 3.3V regulator. The regulator can supply 500mA peak but half of that is drawn by the ESP32, and it's a fairly power-hungry chip. So if you need a ton of power for stuff like LEDs, motors, etc. Use the USB or BAT pins, and an additional regulator

Logic Pins:
This is the general purpose I/O pin set for the microcontroller. All logic is 3.3V
The ESP32 runs on 3.3V power and logic, and unless otherwise specified, GPIO pins are not 5V safe!

Serial Pins:
RX and TX are the additional Serial1 pins, and are not connected to the USB/Serial converter. That means you can use them to connect to UART-devices like GPS's, fingerprint sensors, etc.
The TX pin is the output from the module. The RX pin is the input into the module. Both are 3.3V logic

I2C & SPI Pins:
You can use the ESP32 to control I2C and SPI devices, sensors, outputs, etc. If using with Arduino, the standard Wire and SPI devices work as you'd expect!
Note that the I2C pins do not have pullup resistors already! You must add them if you want to communicate with an I2C device

GPIO & Analog Pins:
There are tons of GPIO and analog inputs available to you for connecting LEDs, buttons, switches, sensors, etc. Here's the remaining pins available.
Bottom row:
A0 - this is an analog input A0 and also an analog output DAC2. It can also be used as a GPIO #26
A1 - this is an analog input A1 and also an analog output DAC1. It can also be used as a GPIO #25
A2 - this is an analog input A2 and also GPI #34. Note it is not an output-capable pin!
A3 - this is an analog input A3 and also GPI #39. Note it is not an output-capable pin!
A4 - this is an analog input A4 and also GPIO #36
A5 - this is an analog input A5 and also GPIO #4
21 - General purpose IO pin #21
Top row:
13 - This is GPIO #13 and also an analog input A12. It's also connected to the red LED next to the USB portIt's also connected to the red LED next to the USB port
12 - This is GPIO #12 and also an analog input A11. This pin has a pull-down resistor built into it, we recommend using it as an output only, or making sure that the pull-down is not affected during boot.
27 - This is GPIO #27 and also an analog input A10
33 - This is GPIO #33 and also an analog input A9. It can also be used to connect a 32 KHz crystal.
15 - This is GPIO #15 and also an analog input A8
32 - This is GPIO #32 and also an analog input A7. It can also be used to connect a 32 KHz crystal.
14 - This is GPIO #15 and also an analog input A6

240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS
Integrated 520 KB SRAM
Integrated 802.11b/g/n HT40 Wi-Fi transceiver, baseband, stack and LWIP
Integrated dual mode Bluetooth (classic and BLE)
4 MByte flash
On-board PCB antenna
Ultra-low noise analog amplifier
Hall sensor
10x capacitive touch interface
32 kHz crystal oscillator
3 x UARTs (only two are configured by default in the Feather Arduino IDE support, one UART is used for bootloading/debug)
2 x I2C (only one is configured by default in the Feather Arduino IDE support)
12 x ADC input channels
2 x I2S Audio
2 x DAC
PWM/timer input/output available on every GPIO pin
OpenOCD debug interface with 32 kB TRAX buffer
SDIO master/slave 50 MHz
SD-card interface support

Package Included:
1 x ESP32 Dev Module WiFi + Bluetooth Flash


Payment

1.We accept PayPal only.
2.All major credit cards are accepted through secure payment processor PayPal.
3.Payment must be received within 7 business days of sale closing.
4.We ship to your or Paypal address. Please make sure your and Paypal address is correct before you pay.

Shipping

1.We ship to your or Paypal address. Please make sure your and Paypal address is correct before you pay.
2.Items will be shipped within 1-3 business day when we received payment.
3.Delivery time depends on destination and other factors;
4.International buyers please note:
a.Import duties, taxes and charges are not included in the item price or shipping charges. These charges are buyer’s responsibility. We will try our best to reduce the risk of the custom duties.
b.Please check with your country's customs office to determine what these additional costs will be prior to buying.

On Oct-17-17 at 23:45:11 PDT, seller added the following information:



Buy Now

Arduino Led Diodes Debugging Module For Arduino Mega, Uno Module, Shield, Bar picture
Arduino Led Diodes Debugging Module For Arduino Mega, Uno Module, Shield, Bar


Texas Instruments P/n: 296-17259-nd Evaluation Module For Bq24103 P/n: Acx1723-n picture
Texas Instruments P/n: 296-17259-nd Evaluation Module For Bq24103 P/n: Acx1723-n


Xilinx Fpga Artix7 Artix-7 Development Board Xc7a35t 256mb Ddr3 picture
Xilinx Fpga Artix7 Artix-7 Development Board Xc7a35t 256mb Ddr3


Xilinx Fpga Artix7 Artix-7 Development Board Xc7a35t 32mb Sdram picture
Xilinx Fpga Artix7 Artix-7 Development Board Xc7a35t 32mb Sdram


Popular Forums