When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Polar Air
by Eaton Compressor
Best Pricing
Fast Shipping
Highest Quality
Industrial! Polar Air! 5HP 2 Cylinder Single Stage AirCompressor Pump
Please note: If paying via credit card or PayPal, there will be a 3% handling fee added to your order
Email Us For Lead Time/Shipping Quote
32CFM Air Compressor cast iron single stage piston series pump, oil lubricated design to extend pump life, rated at up to 50,000 hours (based on B-10 bearing life rating)
This pump can be run with a gasoline engine. It is set up with head unloaders. This will allow the pump to unload the valves in a continuous run application. This is on top of the heads with the small 1/4" lines connecting them. This also allows for complete unloaded, no load start, easy on your gasoline engine starter. You must have an 8-10 HP to run this at a minimum RPM and a 13 HP to run it at maximum RPM. To gauge your motor HP, check the amperage on 220V. It takes 21 amps (running amps) to pull this pump at a 640 RPM speed. The motor used to do this should be a 1750 RPM, 184-T Frame. It will give you a much higher starting torque than a 3450 RPM motor. For an 840 RPM speed, you should use a TRUE 7.5 HP, 32-amp, 215-T Frame, 1750 RPM motor. A 3450 RPM in this HP is also not recommended because of lower starting torque. This pump can be slowed down by putting a smaller pulley on your motor and it can be run with a 5 HP motor pulling 21 amps on 220V (running amps).
The BEST Warranty Around!
Polar Air by Eaton Compressor backs all their compressors with the best warranty in the industry, and we are not kidding, we did the homework! Our trained service and support team is ready if you ever need them and we carry a full line of new replacement parts.
Solid cast iron single stage piston series pump, oil lubricated design to extend pump life, rated at up to 50,000 hours (based on B-10 bearing life rating)
The Eaton Compressor delivers overwhelming performance to ensure that they meet the needs of the most demanding environments. Our Pumps require less maintenance, service, and downtime than any other compressors in the Air Industries. All our Products are designed with exacting tolerance and specifications to deliver all the power that is needed at the job site, garage or shop.
This pump can be run with a gasoline engine. It is set up with head unloaders. This will allow the pump to unload the valves in a continuous run application. This is on top of the heads with the small 1/4" lines connecting them. This also allows for complete unloaded, no load start, easy on your gasoline engine starter. You must have an 8-10 HP to run this at a minimum RPM and a 13 HP to run it at maximum RPM. To gauge your motor HP, check the amperage on 220V. It takes 21 amps (running amps) to pull this pump at a 640 RPM speed. The motor used to do this should be a 1750 RPM, 184-T Frame. It will give you a much higher starting torque than a 3450 RPM motor. For an 840 RPM speed, you should use a TRUE 7.5 HP, 32-amp, 215-T Frame, 1750 RPM motor. A 3450 RPM in this HP is also not recommended because of lower starting torque.
Payment methodPreferred / Accepted
Visa/MasterCard, Amex, Discover
Accepted
Pay on payment instructions
Please do not send payment until You have received an Invoice through . Shipping has to be calculated and applied. Thank you!
Shipping and Handling
Item location: Clayton, Ohio, United States
Services available: Freight - Check the item description or contact the seller for details
Ships to: United States
After receiving the item, contact seller within
Refund will be given as
Return shipping
14 days
Money back
Buyer pays return shipping
Return policy details
Return Policy: All items are returnable ONLY 7 days after customer has received item(s). All item(s) must be returned in the same condition as received. Customer is responsible for all freight when returning item(s). When Eaton Compressor receives the returned item(s), purchaser will be reimbursed for the unit cost, not freight. Anything after 7 days, customer cannot return to seller.
Best Shipping
Highest Quality
$32CFM Air Compressor Pump Specifications: ---Solid cast iron single stage piston series pump, oil lubricated design to extend pump life, rated at up to 50,000 hours (based on B-10 bearing life rating) ---Ram-Tek - solid steel, heavy gauge rods, designed for maximum performance and durability ---Cool-Tek - the coolest running compressors in the industry, air stream technology provides 35% lower operating temperature, reduces moisture build up and extends pump life ---Flow-Tek - concentric disc valves, deliver maximum air flow and reliability with low replacement costs, easily accessible design provides easy maintenance and durability ---Industrial grade ball bearing for maximum performance and extended pump life ---Built-in head unloaders designed for continuous run applications ---Bolt pattern: 10 ¼” in. x 5-3/8 in. ---Pump has a V-Style Pulley – flywheel included on pump ---V-Style Cylinders for maximum cooling ---Solid cast-iron cylinders, crankcase, flywheel, crankshaft, and valve plates ---Large Steel Automotive-Type Filters – not plastic ---Large site glass for viewing your oil level ---dimensions of this pump are: 18” W x 11 3/4” D x 15” H and Flywheel is 14.5 ---weight: 182 Lbs. ---includes oil - hold 2 quarts of oil ---73 DBA “Free Air”: Our 2 Cylinder Heavy Industrial Air Compressor pump with 32 CFM Displacement and a Free Air (usable air) of 19 CFM at 100 PSI can’t be beat. Don't be tricked by air compressor dealers giving you CFM Displacement and you think you are getting the Free Air...and you are really not. For instance, this pump has 32 CFM Replacement. I have seen companies advertise this as "32 CFM at 125 PSI"--this is not true! Displacement is the bore of the cylinder times the distance in the piston stroke times the RPM at zero pressure, but as you go up in pressure, you will lose efficiency on your pump. The CFM will diminish from 32 to 26 at 90 PSI. We give you the "Free Air" at Pressure and the CFM Displacement--NO TRICKS!!! This pump has a maximum PSI of 150. The minimum RPM is 600 and a maximum RPM of 840. This pump can be run with a gasoline engine. It is set up with head unloaders. This will allow the pump to unload the valves in a continuous run application. This is on top of the heads with the small 1/4" lines connecting them. This also allows for complete unloaded, no load start, easy on your gasoline engine starter. You must have an 8-10 HP to run this at a minimum RPM and a 13 HP to run it at maximum RPM. To gauge your motor HP, check the amperage on 220V. It takes 21 amps (running amps) to pull this pump at a 640 RPM speed. The motor used to do this should be a 1750 RPM, 184-T Frame. It will give you a much higher starting torque than a 3450 RPM motor. For an 840 RPM speed, you should use a TRUE 7.5 HP, 32-amp, 215-T Frame, 1750 RPM motor. A 3450 RPM in this HP is also not recommended because of lower starting torque. This pump can be slowed down by putting a smaller pulley on your motor and it can be run with a 5 HP motor pulling 21 amps on 220V (running amps).Best Pricing
Fast Shipping
Highest Quality
Polar Air
by Eaton Compressor
Industrial! Polar Air! 5HP 2 Cylinder Single Stage AirCompressor Pump
Please note: If paying via credit card or PayPal, there will be a 3% handling fee added to your order
Email Us For Lead Time/Shipping Quote
32CFM Air Compressor cast iron single stage piston series pump, oil lubricated design to extend pump life, rated at up to 50,000 hours (based on B-10 bearing life rating)
This pump can be run with a gasoline engine. It is set up with head unloaders. This will allow the pump to unload the valves in a continuous run application. This is on top of the heads with the small 1/4" lines connecting them. This also allows for complete unloaded, no load start, easy on your gasoline engine starter. You must have an 8-10 HP to run this at a minimum RPM and a 13 HP to run it at maximum RPM. To gauge your motor HP, check the amperage on 220V. It takes 21 amps (running amps) to pull this pump at a 640 RPM speed. The motor used to do this should be a 1750 RPM, 184-T Frame. It will give you a much higher starting torque than a 3450 RPM motor. For an 840 RPM speed, you should use a TRUE 7.5 HP, 32-amp, 215-T Frame, 1750 RPM motor. A 3450 RPM in this HP is also not recommended because of lower starting torque. This pump can be slowed down by putting a smaller pulley on your motor and it can be run with a 5 HP motor pulling 21 amps on 220V (running amps).
Payment methodPreferred / Accepted
Visa/MasterCard, Amex, Discover
Accepted
Pay on payment instructions
Please do not send payment until You have received an Invoice through . Shipping has to be calculated and applied. Thank you!
ShippingShipping and Handling
Item location: Clayton, Ohio, United States
Services available: Freight - Check the item description or contact the seller for details
Ships to: United States
ReturnsAfter receiving the item, contact seller within
Refund will be given as
Return shipping
14 days
Money back
Buyer pays return shipping
Return policy details
Return Policy: All items are returnable ONLY 7 days after customer has received item(s). All item(s) must be returned in the same condition as received. Customer is responsible for all freight when returning item(s). When Eaton Compressor receives the returned item(s), purchaser will be reimbursed for the unit cost, not freight. Anything after 7 days, customer cannot return to seller.
Highest Shipping
Best Pricing
32CFM Air Compressor cast iron single stage piston series pump, oil lubricated design to extend pump life, rated at up to 50,000 hours (based on B-10 bearing life rating)
This pump can be run with a gasoline engine. It is set up with head unloaders. This will allow the pump to unload the valves in a continuous run application. This is on top of the heads with the small 1/4" lines connecting them. This also allows for complete unloaded, no load start, easy on your gasoline engine starter. You must have an 8-10 HP to run this at a minimum RPM and a 13 HP to run it at maximum RPM. To gauge your motor HP, check the amperage on 220V. It takes 21 amps (running amps) to pull this pump at a 640 RPM speed. The motor used to do this should be a 1750 RPM, 184-T Frame. It will give you a much higher starting torque than a 3450 RPM motor. For an 840 RPM speed, you should use a TRUE 7.5 HP, 32-amp, 215-T Frame, 1750 RPM motor. A 3450 RPM in this HP is also not recommended because of lower starting torque. This pump can be slowed down by putting a smaller pulley on your motor and it can be run with a 5 HP motor pulling 21 amps on 220V (running amps).
POLAR TECH 904 Corner Protector,EPS Foam,PK128 12F326 POLAR TECH 904
$68.40
POLAR TECH 900 Corner Protector,EPS Foam,3 in L,PK180 12F324 POLAR TECH 900
$60.91
POLAR ELECTRONIC INDUSTRIES SA3C-4 AMPLIFIER SPLITTER 552897
$569.05
Popular Forums