When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
The F800 Series is a VFD range which has been optimized for maximum energy savings with pump and fan control. F800 is equally at home in an industrial environment or in the residential / commercial sector as part of an integrated HVAC solution.
Notes:
* Drive Sizes up to 40HP
** Requires the use of the FR-LU08 keypad
F800 Ratings, 240V Class
Model Number
AMPS for Duty
HP For Duty (NEC)
Frame Size
Cooling Method
Protective Rating
Stocked Item
SLD
LD
SLD
LD
FR-F820-00046-3-N6
4.6
4.2
1
1
A
Self-Cooling
UL Type 1- Plenum Rated
S
FR-F820-00077-3-N6
7.7
7
2
2
B
S
FR-F820-00105-3-N6
10.5
9.6
3
3
C
Forced Air Cooling
S
FR-F820-00167-3-N6
16.7
15.2
5
5
C
S
FR-F820-00250-3-N6
25
23
7.5
7.5
C
S
FR-F820-00340-3-N6
34
31
10
10
D
S
FR-F820-00490-3-N6
49
45
20
15
D
S
FR-F820-00630-3-N6
63
58
20
20
E
S
FR-F820-00770-3-N6
77
70.5
25
25
F
S
FR-F820-00930-3-N6
93
85
30
30
F
S
FR-F820-01250-3-N6
125
114
40
40
F
S
FR-F820-01540-3-60
154
140
60
50
G
IP00
S
FR-F820-01870-3-60
187
170
60
60
H
S
FR-F820-02330-3-60
233
212
75
75
H
S
FR-F820-03160-3-60
316
288
125
100
K
S
FR-F820-03800-3-U6
380
346
150
125
L
S
FR-F820-04750-3-U6
475
432
150
150
L
-
Note: Drives in Shaded Area MUST be used together withFR-HEL DC Link Choke (supplied separately)
FR-HEL DC Link Chokes (supplied separately)
Model Number
LD
SLD
FR-F820-03160-3-60
FR-HEL-75K
FR-HEL-75K
FR-F820-03800-3-U6
FR-HEL-90K
FR-HEL-110K
FR-F820-04750-3-U6
FR-HEL-110K
FR-HEL-110K
F800 Ratings, 480V Class
Model Number
AMPS for Duty
HP For Duty (NEC)
Frame Size
Cooling Method
Protective Rating
Stocked Item
SLD
LD
SLD
LD
FR-F840-00023-3-N6
2.3
2.1
1
1
C
Self - Cooling
UL Type 1 – Plenum Rated
S
FR-F840-00038-3-N6
3.8
3
2
2
C
S
FR-F840-00052-3-N6
5.2
4.8
3
3
C
S
FR-F840-00083-3-N6
8.3
7.6
5
5
C
S
FR-F840-00126-3-N6
12.6
11.5
7.5
7.5
C
S
FR-F840-00170-3-N6
17
16
10
10
D
Forced Air Cooling
S
FR-F840-00250-3-N6
25
23
15
15
D
S
FR-F840-00310-3-N6
31
29
20
20
E
S
FR-F840-00380-3-N6
38
35
25
25
E
S
FR-F840-00470-3-N6
47
43
30
30
F
S
FR-F840-00620-3-N6
62
57
40
40
F
S
FR-F840-00770-3-60
77
70
60
50
G
IP00
S
FR-F840-00930-3-60
93
85
60
60
H
S
FR-F840-01160-3-60
116
106
75
75
H
S
FR-F840-01800-3-60
180
144
150
100
H
S
FR-F840-02160-3-U6
216
180
150
150
J
S
FR-F840-02600-3-U6
260
216
200
150
J
S
FR-F840-03250-3-U6
325
260
250
200
L
S
FR-F840-03610-3-U6
361
325
300
250
L
S
FR-F840-04320-3-U6
432
361
350
300
M
S
FR-F840-04810-3-U6
481
432
400
350
M
S
FR-F840-05470-3-U6
547
481
450
400
N
S
FR-F840-06100-3-U6
610
547
500
450
N
S
FR-F840-06830-3-U6
683
610
550
500
N
S
FR-F842-07700-3-U6 +
FR-CC2-H355K-60
-
683
-
550
P+R
S
FR-F842-07700-3-U6 +
FR-CC2-H400K-60
770
-
650
-
P+S
S
FR-F842-08660-3-U6 +
FR-CC2-H400K-60
-
770
-
650
P+S
S
FR-F842-08660-3-U6 +
FR-CC2-H450K-60
866
-
700
-
P+S
S
FR-F842-09620-3-U6 +
FR-CC2-H450K-60
-
866
-
700
Q+S
S
FR-F842-09620-3-U6 +
FR-CC2-H500K-60
962
-
800
-
Q+S
S
FR-F842-10940-3-U6 +
FR-CC2-H500K-60
-
962
-
800
Q+S
S
FR-F842-10940-3-U6 +
FR-CC2-H560K-60
1094
-
900
-
Q+S
S
FR-F842-12120-3-U6 +
FR-CC2-H560K-60
-
1094
-
900
Q+S
S
FR-F842-12120-3-U6 +
FR-CC2-H630K-60
1212
-
1000
-
Q+S
S
Note: Weights of the drive and the CC2 modules are COMBINED.Drives in Shaded Area MUST be used together with FR-HEL-H DC Link Choke(supplied separately).
FR-HEL-H DC Link Chokes (Supplied Separately)
Model Number
LD
SLD
FR-F840-01800-3-60
FR-HEL-H75K
FR-HEL-H90K
FR-F840-02160-3-U6
FR-HEL-H90K
FR-HEL-H110K
FR-F840-02600-3-U6
FR-HEL-H110K
FR-HEL-H132K
FR-F840-03250-3-U6
FR-HEL-H132K
FR-HEL-H160K
FR-F840-03610-3-U6
FR-HEL-H160K
FR-HEL-H185K
FR-F840-04320-3-U6
FR-HEL-H185K
FR-HEL-H220K
FR-F840-04810-3-U6
FR-HEL-H220K
FR-HEL-H250K
FR-F840-05470-3-U6
FR-HEL-H250K
FR-HEL-H280K
FR-F840-06100-3-U6
FR-HEL-H280K
FR-HEL-H315K
FR-F840-06830-3-U6
FR-HEL-H315K
FR-HEL-H355K
F800 General Specifications
Operation Specifications
Control Method
Soft-PWM control, high carrier frequency PWM control (selectable among V/F control (Optimum excitation control), advanced magnetic flux vector control (Advanced optimum excitation control) and PM motor control)
Output Frequency Range
0.2 to 590 Hz (The upper-limit frequency is 400 Hz under Advanced magnetic flux vector control, and PM motor control.)
Frequency Setting Resolution
Analog Input
0.015 Hz/60 Hz (terminal 2, 4: 0 to 10 V/12 bits)
0.03 Hz/60 Hz (0 to 5 V/11 bits or 0 to 20 mA/approx. 11 bits for terminals 2 and 4,
0 to ±10 V/12 bits for terminal 1)
0.06 Hz/60 Hz (0 to ±5 V/11 bits for terminal 1)
Digital Input
0.01Hz
Frequency Accuracy
Analog Input
Within ±0.2% of the max. output frequency (25°C ±10°C)
Digital Input
Within 0.01% of the set output frequency
Voltage / Frequency Characteristics
Base frequency can be set from 0 to 590 Hz. Constant-torque/variable-torque pattern or adjustable 5 points V/F can be selected.
Starting Torque
Induction Motor
120% 0.5 Hz (Advanced magnetic flux vector control)
IPM Motor
50%
Torque Boost
Manual torque boost
Acceleration / Deceleration Time Setting
0 to 3600 s (acceleration and deceleration can be set individually), linear or S-pattern acceleration/deceleration mode, backlash countermeasures acceleration/deceleration can be selected
DC Injection Brake
(Induction Motor)
Operation frequency (0 to 120 Hz), operation time (0 to 10 s), operation voltage (0 to 30%) variable
Stall Prevention Operation Level
Activation range of stall prevention operation (SLD rating: 0 to 120%, LD rating: 0 to 150%). Whether to use the stall prevention or not can be selected. (V/F control, Advanced magnetic flux vector control)
Frequency Setting Signal
Analog Input
Terminals 2 and 4: 0 to 10 V, 0 to 5 V, 4 to 20 mA (0 to 20 mA) are available.
Terminal 1: -10 to +10 V, -5 to 5 V are available.
Digital Input
Input using the setting dial of the operation panel or the parameter unit. Four-digit BCD or 16-bit binary (when used with option FR-A8AX)
Start Signal
Start signal Forward and reverse rotation or start signal automatic self-holding input
(3-wire input) can be selected.
Input Signal
Low-speed operation command, Middle-speed operation command, High-speed operation command, Second function selection, Terminal 4 input selection, Jog operation selection, Output stop, Start self-holding selection, Forward rotation command, Reverse rotation command, Inverter reset. The input signal can be changed using Pr.178 to Pr.189 (input terminal function selection).
Pulse Train Input
100kpps
Operational Functions
Maximum and minimum frequency settings, multi-speed operation, acceleration/deceleration pattern, thermal protection, DC injection brake, starting frequency, JOG operation, output stop (MRS), stall prevention, regeneration avoidance, increased magnetic excitation deceleration, DC feeding (*1), frequency jump, rotation display, automatic restart after instantaneous power failure, electronic bypass sequence, remote setting, retry function, carrier frequency selection, fast response current limit, forward/reverse rotation prevention, operation mode selection, slip compensation, speed smoothing control, traverse, auto tuning, applied motor selection, RS-485 communication, PID control, PID pre-charge function, cooling fan operation selection, stop selection (deceleration stop/coasting), power-failure deceleration stop function, PLC function, life diagnosis, maintenance timer, current average monitor, multiple rating, test run, 24 V power supply input for control circuit, safety stop function, self power management, BACnet communication, PID gain tuning, cleaning, load characteristics storage, emergency drive (*1)
Output Signals
Open Collector Output (Five Terminals) Relay Output (Two Terminals)
Inverter running, Up to frequency, Instantaneous power failure/undervoltage (*1), Overload warning, Output frequency detection, Fault. The output signal can be changed using Pr.190 to Pr.196 (output terminal function selection). Fault codes of the inverter can be output (4 bits) from the open collector.
Pulse Train Output (FM Type)
50 kpps
Indication
For Meter
Pulse Train Output (FM Type)
Max. 2.4 kHz: one terminal (output frequency)
The monitored item can be changed using Pr.54 FM/CA terminal function selection.
Current Output (CA Type)
Max. 20 mADC: one terminal (output current)
The monitored item can be changed using Pr.54 FM/CA terminal function selection.
Voltage Output
Max. 10 VDC: one terminal (output voltage)
The monitored item can be changed using Pr.158 AM terminal function selection.
Operation Panel
(FR-DU08)
Operating Status
Output frequency, output current, output voltage, frequency setting value
The monitored item can be changed using Pr.52 Operation panel main monitor selection.
Fault Record
Fault record is displayed when a fault occurs. Past 8 fault records and the conditions immediately before the fault (output voltage/current/frequency/cumulative energization time/year/month/date/time) are saved.
Protective / Warning Function
Overcurrent trip during acceleration, Overcurrent trip during constant speed, Overcurrent trip during deceleration or stop, Regenerative overvoltage trip during acceleration, Regenerative overvoltage trip during constant speed, Regenerative overvoltage trip during deceleration or stop, Inverter overload trip (electronic thermal relay function), Motor overload trip (electronic thermal relay function), Heatsink overheat, Instantaneous power failure (*1), Undervoltage (*1), Input phase loss (1, *2), Stall prevention stop, Loss of synchronism detection (*2), Upper limit fault detection, Lower limit fault detection, Output side earth (ground) fault overcurrent, Output short circuit, Output phase loss, External thermal relay operation (*2), PTC thermistor operation (*2), Option fault, Communication option fault, Parameter storage device fault, PU disconnection, Retry count excess (*2), CPU fault, Operation panel power supply short circuit/RS-485 terminals power supply short circuit, 24 VDC power fault, Abnormal output current detection (*2), Inrush current limit circuit fault(*1), Communication fault (inverter), Analog input fault, USB communication fault, Safety circuit fault, Overspeed occurrence (*2), 4 mA input fault (*2), Pre-charge fault (*2), PID signal fault (*2), Internal circuit fault, User definition error in the PLC function. Fan alarm, Stall prevention (overcurrent), Stall prevention (overvoltage), Electronic thermal relay function
pre-alarm, PU stop, Parameter copy, Safety stop, Maintenance timer 1 to 3 (*2), USB host error, Operation panel lock (*2), Password locked (*2), Parameter write error, Copy operation error, 24 V external power supply operation, Load fault warning, Emergency drive in operation (*1)
Environment
Ambient Temperature
-10°C to +50°C (non-freezing) (LD rating)
-10°C to +40°C (non-freezing) (SLD rating)
Ambient Humidity
With circuit board coating (conforming to IEC60721-3-3 3C2/3S2): 95% RH or less (non-condensing). Without circuit board coating: 90% RH or less (non-condensing)
Storage Temperature (*3)
-20°C to +65°C
Atmosphere
Indoors (without corrosive gas, flammable gas, oil mist, dust and dirt, etc.)
Altitude / Vibration
Maximum 1000 m above sea level (*4), 5.9 m/s² or less (*5) at 10 to 55 Hz (directions of X, Y, Z axes)
Notes:
1. Available only for the standard model.<
2. This protective function is not available in the initialstatus.
3. Temperature applicable for a short time, e.g. in transit.
4. For the installation at an altitude above 1,000 m (up to2,500 m), derate the rated current 3% per 500 m.
5. 2.9 m/s² or less for the FR-F840-04320(185K) or higher.
F800 Series Terminal Connection Diagram (Version with 0-20mAAnalog Output Signal)
CA Type
Notes:
1. For the FR-F820-03160 (75K) or higher, the FR-F840-01800(75K) or higher, always connect a DC reactor (FR-HEL), which is available as anoption.
2. When using separate power supply for the control circuit,remove the jumper between R1/L11 and S1/L21.
3. The function of these terminals can be changed with theinput terminal assignment (Pr.178 to Pr.189).
4. Terminal JOG is also used as the pulse train inputterminal. Use Pr.291 to choose JOG or pulse.
5. Terminal input specifications can be changed by analoginput specification switchover (Pr.73, Pr.267). To input a voltage, set thevoltage/current input switch OFF. To input a current, set the voltage/currentinput switch ON. Terminals 10 and 2 are also used as a PTC input terminal.(Pr.561)
6. It is recommended to use 2 W 1 kΩ when the frequencysetting signal is changed frequently.
7. Do not use terminals PR and PX. Do not remove the jumperconnected to terminals PR and PX.
8. The function of these terminals can be changed with theoutput terminal assignment (Pr.195, Pr.196).
9. The function of these terminals can be changed with theoutput terminal assignment (Pr.190 to Pr.194).
10. No function is assigned in the initial status. Assignthe function using Pr.186 CS terminal function selection.
F802 Series Terminal Connection Diagram (Version with 0-20mAAnalog Output Signal)
Notes:
1. The terminals R1/L11 and S1/L21 are connected to theterminals P/+ and N/- with a jumper respectively. When using separate powersupply for the control circuit, remove the jumpers from R1/L11 and S1/L21.
2. The function of these terminals can be changed with theinput terminal assignment (Pr.178 to Pr.189).
3. Terminal JOG is also used as the pulse train inputterminal. Use Pr.291 to choose JOG or pulse.
4. The X10 signal (NC contact input specification) isassigned to the terminal MRS in the initial setting. Set Pr.599 = \"0\"to change the input specification of the X10 signal to NO contact.
5. No function is assigned in the initial setting. UsePr.186 for function assignment.
6. Terminal input specifications can be changed by analoginput specification switchover (Pr.73, Pr.267). To input a voltage, set thevoltage/current input switch OFF. To input a current, set the voltage/currentinput switch ON. Terminals 10 and 2 are also used as a PTC input terminal.(Pr.561)
7. It is recommended to use 2 W 1 kΩ when the frequencysetting signal is changed frequently.
8. The function of these terminals can be changed with theoutput terminal assignment (Pr.195, Pr.196).
9. The function of these terminals can be changed with theoutput terminal assignment (Pr.190 to Pr.194).
10. No function is assigned in the initial setting. UsePr.192 for function assignment.
11. The terminal F/C (FM) can be used to output pulse trainsas open collector output by setting Pr.291.
12. Not required when calibrating the scale with theoperation panel.
F800 Dimensions – Frame Size Key
Dimensions, 230V and 480V Drives
Series
Height
Width
Depth
FR-F800
A
12.2 (310)
4.33 (110)
4.39 (112)
B
12.2 (310)
4.33 (110)
4.98 (127)
C
12.52 (318)
5.91 (150)
5.57 (141.6)
D
12.76 (324)
8.66 (220)
6.69 (170)
E
14.29 (363)
8.66 (220)
7.48 (190)
F
20.37(517)
9.84 (250)
7.48 (190)
G
21.67 (550)
12.80 (325)
7.68 (195)
H
21.67 (550)
17.13 (435)
9.84 (250)
J
24.41 (620)
18.31 (465)
11.81 (300)
K
27.56 (700)
18.31 (465)
9.84 (250)
L
29.13 (740)
18.31 (465)
14.17 (360)
M
39.76 (1010)
19.61 (498)
14.96 (380)
N
39.76 (1010)
26.77 (680)
14.96 (380)
FR-F842
P
52.4 (1330)
21.3 (540)
17.3 (440)
Q
62.2 (1580)
26.8 (680)
17.3 (440)
FR-CC2-H
R
52.4 (1330)
23.6 (600)
17.3 (440)
S
62.2 (1580)
23.6 (600)
17.3 (440)
F800 Series Options and Accessories
Model Number
Description
Comments
Stocked Item
FR-A8AX
16 Bit Digital Input Card
BCD or Binary input
S
FR-A8AY
Digital Output / Extended Analog Output Card
2 extra 0-20 mA or 0-10V output signals
S
FR-A8AC
120V Input Card
Use 120V signals to control the drive
S
FR-A8AR
Relay Output Card
3 extra independent type \'C\' relays
S
FR-A8NC
CC-Link Communications Card
S
A8NC-CON
CC-Link Communications Card and connectors
Includes FR-A8NC and 2 x A6NC-CON plugs
S
FR-A8ND
DeviceNet Communications Card
S
FR-A8NP
Profibus DPV0 Communications Card
S
A8NDPV1
Profibus DPV1 Communications Card
S
A8NEIP-2P
EtherNET IP Communications Card
S
A8NPRT-2P
Profinet Communications Card
S
FR-A8NCE
CC-Link IE Communications Card
S
FR-LU08
Liquid Crystal Operation Panel (Alphanumeric)
Mount on VFD or panel
S
FR-PU07
Parameter Unit
Mount on panel only
S
FR-PU07-01
Parameter Unit (HVAC type)
Modified version for HVAC applications
S
FR-PU07BB-L
Parameter Unit with Battery Back-up
Hand held. Can program unpowered drives
S
FR-CB20_ _= 1,3,5
Parameter Unit Connection Cable
1, 3 or 5 meter lengths
S
FR-ADP
Keypad Adaptor Unit
Connect FR-DU08 or FR-LU08 to FR-CB2
S
FR-A8TAT
Control Terminal Block Adaptor
Use A500 or A700 terminal block with A800
S
FR-A8TR
Screw Terminal Block Option
Screw terminal block adaptor
(use with FR-ATAT)
-
FR-HC2
Zero Harmonic Controller
Active Bridge Front End
(*1)
FR-HEL, FR-HEL-H
DC Link Choke
Use in accordance with selection guide
S
FR-Configurator2
Software setup utility for 800 series
S
Note 1: Some versions are held in stock - consult salesoffice for details.
Dimensions of REQUIRED DC Link Chokes
(supplied separately) Unit of measure: inches (mm)
Height
Width
Depth
Weight (lbs)
FR-HEL-75K
13.39 (340)
5.91 (150)
7.87 (200)
37.4
FR-HEL-90K
13.39 (340)
5.91 (150)
7.87 (200)
41.8
FR-HEL-H75K
12.60 (320)
5.51 (140)
7.28 (185)
35.2
FR-HEL-H90K
13.39 (340)
5.91 (150)
7.48 (190)
44
FR-HEL-H110K
13.39 (340)
5.91 (150)
7.68 (195)
48.4
FR-HEL-H132K
15.94 (405)
6.89 (175)
7.87 (200)
57.2
FR-HEL-H160K
15.94 (405)
6.89 (175)
8.07 (205)
61.6
FR-HEL-H185K
15.94 (405)
6.89 (175)
9.45 (240)
63.8
FR-HEL-H220K
15.94 (405)
6.89 (175)
9.45 (240)
66
FR-HEL-H250K
17.32 (440)
7.48 (190)
9.84 (250)
77
FR-HEL-H280K
17.32 (440)
7.48 (190)
10.04 (255)
83.6
FR-HEL-H315K
19.49 (495)
8.27 (210)
9.84 (250)
92.4
FR-HEL-H355K
19.49 (495)
8.27 (210)
9.84 (250)
101.2
Mitsubishi F800-E AC Drive FR-F840-00023-E3-N6 1HP 3Ph w/ Keypad Used
$750.00
$999.99
1PCS NEW USB DINV-U4 Cable FOR Mitsubishi inverter E500 E700 A700 F700 A800 F800
$193.41
Popular Forums