This item has been shown 4 times.
The RS-1007 Pro analog clamp meter is an average-sensing, manual-ranging multimeter for measuring current, voltage, and resistance in electrical testing and heating, ventilation, and air-conditioning (HVAC) applications and in environments where very hot or very cold temperatures might interfere with the performance of a digital meter. This analog meter displays measurements with a needle that moves on a calibrated scale. It has a broader operating temperature range than digital multimeters and can be used outdoors. It has a clamp that measures alternating current (AC) to 1,000 amp, and comes with detachable test leads that measure AC voltage to 600 volts (V) and resistance to 1,000 ohms. The clamp has two jaws that close around an electrical conductor up to 1.88" (47 mm) in diameter to measure current without touching or interrupting the circuit. The needle lock secures the needle in place to protect it from damage during transport and to hold it at a reading, even after the meter is disconnected. The resistance measurement also tests for continuity and confirms that the circuit conducts electricity. A finger guard on the body of the meter helps protect fingers from shock.This average-sensing, or average-responding, meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform. It is a manual-ranging meter and requires that the operator choose the appropriate operating range. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category IV installations up to 600V, which covers measurements at the source of the low-voltage supply, such as electricity meters and overcurrent protection devices. The meter comes with a soft vinyl carrying case. The meter does not require batteries for measuring current or voltage.SpecificationsMaximum alternating current (AC) input1,000 ampMaximum AC voltage input600 volt (V)Maximum resistance detected1,000 ohmsPower supply1.5V ANSI/NEDA-24A or IEC LR03 AAA battery (one, installed, for resistance measurement)Fuse0.5 amp/1,000V fast-blow fuse (installed)Standards met and certificationsEuropean Normal (EN) International Electrotechnical Commission (IEC) and EN safety standard 61010-1 European Conformity (CE) Underwriters Laboratories Australia N10140Weight1.05 lb./474 gMeter dimensions10.3 x 4.0 x 1.6 inches/261 x 102 x 41 mm (H x W x D)H is height, the vertical distance from the lowest to highest point W is width, the horizontal distance from left to right D is depth, the horizontal distance from front to back.Clamp meters (also called clamp-on meters) measure electrical current without cutting through wires or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp meters diagnose problems in electrical equipment, wiring, and power supplies. The meter's current clamp has two jaws that fit around a conductor to take measurements. All clamp meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltages determine meter choice. Safety ratings are based on the International Electrotechnical Commission's (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating.Amprobe manufactures electrical testing equipment for commercial, industrial, and home use. The company was founded in 1948 and is headquartered in Everett, WA.Whats in the BoxRS-1007 Pro average-sensing analog clamp multimeter(1) Test lead set(1) 0.5 amp/1,000V fast-blow fuse (installed(1) 1.5V AAA battery (installed)Soft vinyl carrying caseInstructions
- All payments must be prepaid.
- We only accept payment via PayPal. Please kindly check if you can do the payment via PayPal before placing an order. If you don't have PayPal account.
- Payment must be received within 7 days after sales ended. Unpaid dispute will be filed to for the non payable buyers.
- Items are dispatched within 24 hours (except weekends and holidays) and shipped from US.
- Orders from the United States will all be shipped out via USPS. The shipment usually takes 3-7 business days (Saturday and Sunday excluded). If you need the item urgently, please contact us for detail before purchase.
- Orders from Canada or Moxico will all be shipped out via USPS International Service.
The shipment usually takes 7-10 business days (Saturday and Sunday excluded).
If you need the item urgently, please contact us for detail before purchase.
- Local pick up is not available.
- Customers in Porto Rico, Alaska and Hawaii are recommended to contact us for shipping details (shipping cost time) before placing an order.
The warranty shall not apply to the following circumstances:
a) Damage caused by undue ware tear, misuse, improper installation or operation, neglect, accidents.
b) Damage caused by natural disasters, flood fire, lightning or pollution.
c) If item was opened, any parts removed or repaired by any unauthorized person.
d) If damaged parts are the TFT screen or the screen has less than 3 dead pixels.
- This product comes with 30-Days Money Back Guarantee.
- If you receive an item and it doesn't work properly or you don't like it because of any reason at all,
we have a 100% refund/return policy. We will ship you a new item or refund your money for the full sale amount.
- For all returned products, buyers MUST contact us for the returning address.