DSO1202E Oscilloscope /Recorder/DMM/FFT Spectrum Analyzer/Frequency Counter For Sale
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
DSO1202E Oscilloscope /Recorder/DMM/FFT Spectrum Analyzer/Frequency Counter:
$649.49
- About class=\"bigpicu\">
Bandwidth 200MHz Oscilloscope, 1GS/s sample rate, and 6000 Counts DMM with analog bargraph.
Specifications:
ModelDSO1202EAcquisitionSample ModesReal-Time SampleAcquisition Modes
NormalNormal data onlyPeak DetectHigh-frequency and randon glith captureAverageWavefom Average, selectable 4,8,16,32,64,128InputsInputs CouplingAC, DC, GNDInputs Impendance1MΩ±2%‖20pF±3pFProbe Attenuation1X, 10XSupported Probe Attenuation Factor1X, 10X, 100X, 1000XMaximum Input VoltageCAT I and CAT II: 300VRMS (10×), Installation Category;
CAT III: 150VRMS (1×)
Horizontal SystemSample Rate Range1GS/sWaveform Interpolation(sin x)/xRecord Length2MSEC/DIV Range2ns/div~2000s/div, in a2, 4, 8 sequenceSample Rate and
Delay Time Accuracy±50ppm over any≥1ms time intervalScanning Speed Range2ns/div to10ns/div;(-4div×s/div) to 20ms;
Delta Time Measurement Accuracy
(Full Bandwidth)Single-shot, Normal mode:± (1 sample interval +100ppm × reading + 0.6ns);
>16 averages:± (1 sample interval + 100ppm × reading + 0.4ns);
Sample interval = s/div ÷ 200Vertical SystemVertical Resolution8-bit resolution, all channel sampled simultaneouslyVolts Range2mV/div to 100V/div at input BNCBandwidth200MHzRise Time at BNC( typical)1.8nsAnalog Bandwidth in
Normal and Average
modes at BNC or with probe,
DC -, *, /, FFTFFTWindows:Hanning, Flatop, Rectamgular, Bartlett, Blackman; 1024 sample pointBandwidth Limit20MHzLow Frequency Response (-3db)≤10Hz at BNCDC Gain Accuracy±3% for Normal or Average acquisition mode, 100V/div to 10mV/div.
±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div.DC Measurement Accuracy,
Average Acquisition ModeMeasurement Type: Average of≥16 waveforms with vertical position at zero
Accuracy: ± (3% × reading + 0.1div + 1mV) when 10mV/div or greater is selected.
Measurement Type: Average of≥16 waveforms with vertical position not at zero
Accuracy: ± [3% × (reading + vertical position) + 1% of vertical position + 0.2div].Volts Measurement Repeatability,
Average Acquisition ModeDelta volts between any two averages of ≥16 waveforms acquired under same setup and ambient conditionsTrigger SystemTrigger TypesEdge, Video, Pulse, Slope, Over time, AlternativeTrigger SourceCH1, CH2, AC LineTrigger ModesAuto, Normal, SingleCoupling TypeDC, AC, HF Reject, LF Reject, Noise RejectTrigger Sensitivity
(Edge Trigger Type)DC(CH1,CH2):
1div from DC to 10MHz; 1.5div from 10MHz to 100MHz; 2div from 100MHz to Full;
AC: Attenuates signals below 10Hz ;
HF Reject: Attenuates signals above 80kHz;
LF Reject: Same as the DC-coupled limits for frequencies above 150kHz; attenuates signals below 150kHz.Trigger Level RangeCH1/CH2: ±8 divisions from center of screen;Trigger Level Accuracy( typical)Accuracy is for signals having rise and fall times ≥20nsCH1/CH2: 0.2div × volts/div within ±4 divisions from center of screen;Set Level to 50%(typical)Operates with input signals ≥50HzVideo Trigger
Video Trigger TypeCH1, CH2: Peak-to-peak amplitude of 2 divisions;Signal Formats and Field RatesSupports NTSC, PAL and SECAM broadcast systems for any field or any lineHoldoff Range100ns ~ 10sPulse Width Trigger
Pulse Width Trigger ModeTrigger when (< , >, = , or ≠); Positive pulse or Negative pulsePulse Width Trigger PointEqual: The oscilloscope triggers when the trailing edge of the pulse crosses the trigger level.
Not Equal: If the pulse is narrower than the specified width, the trigger point is the trailing edge. Otherwise, the oscilloscope triggers when a pulse continues longer than the time specified as the Pulse Width.
Less than: The trigger point is the trailing edge.
Greater than (also called overtime trigger): The oscilloscope triggers when a pulse continues longer than the time specified as the Pulse WidthPulse Width Range20ns ~ 10sSlope Trigger
Slope Trigger ModeTrigger when (< , > , = , or ≠ ); Positive slope or Negative slopeSlope Trigger PointEqual: The oscilloscope triggers when the waveform slope is equal to the set slope.
Not Equal: The oscilloscope triggers when the waveform slope is not equal to the set slope.
Less than: The oscilloscope triggers when the waveform slope is less than the set slope.
Greater than: The oscilloscope triggers when the waveform slope is greater than the set slope.Time Range20ns ~ 10sOvertime Trigger
Over Time ModeeRising edge or Falling edgeTime Range20ns ~ 10sAlternative Trigger
Trigger on CH1Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger on CH2Internal Trigger: Edge, Pulse Width, Video, SlopeTrigger Frequency Counter
Readout Resolution6 digitsAccuracy (typical)±30ppm (including all frequency reference errors and ±1 count errors)Frequency RangeAC coupled, from 4Hz minimum to rated bandwidthSignal SourcePulse Width or Edge Trigger modes: all available trigger sources
The Frequency Counter measures trigger source at all times, including when the oscilloscope acquisition pauses due to changes in the run status, or acquisition of a single shot event has completed.
Pulse Width Trigger mode: The oscilloscope counts pulses of significant magnitude inside the 1s measurement window that qualify as triggerable events, such as narrow pulses in a PWM pulse train if set to < mode and the width is set to a relatively small time.
Edge Trigger mode: The oscilloscope counts all edges of sufficient magnitude and correct polarity.
Video Trigger mode: The Frequency Counter does not work.MeasureCursor MeasurementManual: Voltage difference between cursors:△V
Time difference between cursors:△T
Reciprocal of△T in Hertz (1/ΔT);
Tracing: The valtage and time at a waveform point;Auto MeasuermentFrequency, Period, Mean, Pk-Pk, Cycli RMS, Minimum, Maximum, Rise time, Fall Time, +Pulse Width, -Pulse Width, Delay1-2Rise, Delay1-2Fall, +Duty, -Duty, Vbase, Vtop, Vmid, Vamp, Overshoot, Preshoot, Preiod Mean, Preiod RMS,Scope Trendplot1.2M PointGeneral SpecificationsDisplay Resolution640 horizontal by 480 vertical pixelsDisplay ContrastAdjustable (16 gears) with the progress barProbe Compensator Output
Output Voltage( typical)About 2Vpp into≥1MΩ loadFrequency(typical)1kHzPower Supply
Supply VoltageAC Input:100-240VACRMS,0.6A MAX,50Hz~60Hz; DC Output:9V,2APower 32℉to 122℉(0℃to 50℃);
Nonoperating: -40℉to 159.8℉(-40℃to +71℃)Cooling MethodConvectionHumidity+104℉or below (+40℃or below): ≤90% relative humidity;
106℉to 122℉(+41℃to 50℃): ≤60% relative humidityAltitudeOperating: Below 3,000m (10,000 feet);
Nonoperaring: Below 15,000m(50,000 feet)Mechanical
Size260mmmm; 220mm; 75mmWeight2.5KG(without Packing)DMM ModesMax. Resolution6000 CountsDMM Testing ModesVoltage, Current, Resistance, Capacitance, Diode & ContinuityMax. Input VoltageAC:600V, DC: 800VMax. Input CurrentAC: 10A, DC:10AInput Impendance10MΩDMM TrendPlot1.2M Voltage60.00mV±1%±1 Voltage60.00mV±1%±3 Current60.00mA±1.5%±1 digit10uA600.0mA±1.5%±1 digit100uA6.000A±2%±3 digit1mA10.00A10mAAC Current60.00mA±1.5%±3 digit10uA600.0mA±1%±1 digit100uA6.000A±1.5%±3 digit1mA10.00A10mAResistance600±1%±3 digit0.1Ω6.000K±1%±1 digit100KΩCapacitance40.00nF±1%±1 the smallest capacitance value that can be measured in 5nFDiode0V~2.0VON-OFF test<10Ω
Function Picture
Standard Accessories:
- About Us
- Payment
- Shipping
- Terms
- Returns
1. Our working time is Mon.~Sat. 9:00~20:00. 2. Message or emails will be replied within 24 hours.If you can’t receive our reply, please send again, we will reply asap. 3. Or please call us via phone, Mandarin, Cantonese, English, Japanese is available. Please payvia Paypal.
1. The item will be shipped out viaEXPRESS POST in 1 business day after payment cleared. Normally 2~4 WORKING days for receiving. 2.AU &US,item will be posted with e-packageservice,other placeswith China / Hong Kong / Singaporepost service. 3.Kindly please find below delivery time on our shipping.
Country
Delivery Time
Working Days
5-7
8-11
12-14
15-19
20-22
>30
Working Days + Sat.+Sun.
5-9
10-15
16-20
21-25
26-30
>40
United States
Rate(Time Arrived)
15.5%
70.5%
9.5%
5.5%
0%
Resend / Refund
United Kingdom
Rate(Time Arrived)
9.9%
63.2%
19.1%
3.4%
3.4%
Resend / Refund
Canada
Rate(Time Arrived)
0%
47.1%
31.4%
17.6%
3.9%
Resend / Refund
Australia
Rate(Time Arrived)
14.4%
50.0%
21.4%
8.2%
6%
Resend / Refund
Germany
Rate(Time Arrived)
11.1%
22.2%
30.3%
20.9%
15.5%
Resend / Refund
Spain
Rate(Time Arrived)
3.5%
47.9%
25.0%
12.9%
10.7%
Resend / Refund
Italy
Rate(Time Arrived)
2.5%
10.2%
31.3%
18.2%
17.3%
Resend / Refund
Rate(Time Arrived)
0%
13.1%
43.3%
28.1%
15.5%
Resend / Refund(>50)
***: South America is much longer than the others normally, and Russia Post, theresend/refund days is 50 days. 4. We provide DHL / EMS (5~9 WORKING days), too. But cost is around 20usd or higher. Please contact us if you prefer to. 5.As delivered time descripted repeatedly, please don't leftlow star evaluation or neutral or negative response on post.6. Package will ship as per buyer's paypal registered address, so please make sure no miss on your address.
1.Incomingdamaged or defective when you receive, please contact us within14 days after receiving the item. 2.Replacementor refund will be proceeded once defectconfirmed. 3. Please be reminded when return, the items should bewith original shape ( original packing, accessories, unused item…). 4. Except incoming defect,returning shipping fee is handled by buyer. 5.Custom tax fee won't be charged if occur, please let us know any concern when you place the order. 1. 30 days money back & return guarantee.2. Buyer pays return post fee.
Related Items:
Warning: Invalid argument supplied for foreach() in /home/bbforums/public_html/store/relateditems.php on line 72
